An Invitation for a Girl’s Party

#v12198

The invitation and the table decoration are made from card and beads. The little hanger is made from silver-plated wire and compliments the small dress perfectly.

Sélectionnez des produits pour cette idée

{{ optionsGroup.label }}

{{ getVariantsButtonText(option) }}
   
 
 
   
 
 
   
 
 
   
 
 
   
 
 
Prix ​​total
{{ getFormattedBundlePrice() }}

{{ getRewardMessage() }}

Guide step %d
1   Cut out the dress, the collar and the petticoat from the template in matching colours.
Guide step %d
2   Assemble the parts with double-sided adhesive tape and 3D foam pads.
Guide step %d
3   Attach a ribbon around the waist of the dress and fasten it on the back. For the bow, cut a piece of ribbon measuring approx. 20cm, tie the bow and attach it to the belt with a 3D foam pad. Trim the ends. Decorate the small collar with self-adhesive rhinestone half-pearls.
Guide step %d
4   Cut a piece of silver-plated wire for the hanger. Double over the wire and twist a couple of times and form it. Bend the ends to form a small loop.
Guide step %d
5   Attach the hanger onto the card. Attach 3D foam pads and attach the hanger with another two 3D foam pads.
Guide step %d
6   Attach the dress to the hanger with 3D foam pads. Use two 3D foam pads on top of each other to achieve the same height as the hanger.
Guide step %d
7   Make a small border and attach it to the card with double-sided adhesive tape.
Guide step %d
8   For the bead coil, cut a piece of wire measuring 20cm. Pull beads onto the wire and twist the wire around a darning needle.
Guide step %d
9   Push a hole through the card and attach the bead coil.
Guide step %d
10   Cut a piece of paper. Attach the paper over the wire ends on the back with double-sided adhesive tape.
Guide step %d
13   Place Cards: Cut a piece of silver-plated wire measuring 25cm. Twist to form a small loop at the end. Pull seven red and seventy orange beads onto the wire.
Guide step %d
14   Bend the flower head around the silver-plated wire.
Guide step %d
15   Form the petals and close the flower.
Guide step %d
16   Pull a bead onto the end of the silver-plated wire.
Guide step %d
17   Cut a new piece of silver-plated wire and twist it around the stalk.
Guide step %d
18   Form the leaves.
Guide step %d
19   Twist the wire around the leaves.
Guide step %d
20   Pull a bead onto the end of the wire and bend to form a coil.
Guide step %d
21   Bend to form a hook for hanging onto the glass.
Guide step %d
22   Cut a piece of card for the place card which is attached onto the flower stalk with double-sided adhesive tape.
Guide step %d
23   A place card.
Guide step %d
24   A Napkin Ring: Make a flower following the same procedure as for the place card. Feed a 30cm long piece of wire through the middle of the flower, double over and twist.
Guide step %d
25   Bend the wire to a suitable size. Feed the wire through the middle of the flower.
Guide step %d
26   Twist the wire around the ring.
Guide step %d
27   The finished napkin ring.
Guide step %d
Gabarit   -
Pièce jointe: Télécharger
Allez aussi explorer dans
Retour
Je fais mes courses comme
Continuer comme guest
Les avantages à se connecter

✔ Votre liste de souhaits personnelle

✔ L’historique de vos commandes

✔ Paiement facile
Les avantages à se connecter

✔️ Vos prix spéciaux

✔️ Des produits réservés aux professionnels

✔️ L’univers marketing B2B
Les avantages à se connecter

✔ Des contenus spécialement conçus pour vous

✔ Vos prix spéciaux
Copyright © 2021-present | Creativ Company France. All rights reserved | 70 avenue de Clichy | 75017 Paris | France | 01.76.75.31.13 | info@cchobby.fr